Surgeon subjectivity may play a role in graft failure when the fixation device is incorrectly tensioned or not suitable for the situation at hand. Dr Frank Noyes explains...
First published 2008, and reviewed August 2023 by Dr Sheila Strover (Clinical Editor)
ACL reconstruction failure and revisions - course
- continued - "Most common causes of ACL graft failure"...
- ACL graft failure due to graft impingement
- ACL graft failure due to problems in graft tensioning and fixation
- ACL graft failure due to failure to address associated instabilities
- ACL graft failure due to inadequate rehabilitation programme
- Compounding problems that must be addressed in revision ACL surgery
- Graft options in revision ACL
- Contraindications to ACL revision
- What can one expect after ACL revision?
There is some controversy both about the optimal tension that should be applied to a graft, and also about the best fixation devices to use.
In these matters the surgeon must exercise considerable judgement. If the surgeon make a poor judgement of tension or a poor choice of fixation, this may contribute to graft failure.
Improper tensioning of graft prior to fixation
Before the surgeon fixes the graft in position, the graft needs to be 'tensioned' correctly, and this, too, is largely a matter of clinical judgement. As patients differ in the amount of normal ligament laxity, tensioning is usually performed in relation to the 'good' leg. If it is too loose, the knee will be unstable. If too tight, then the graft will be under strain and may break.
Poor choice of fixation
The type of fixation is to a large extent dictated by whether or not the harvested graft has a bone block -
Grafts with a bone block at either end
The most advantageous graft in terms of fixation is the bone-patellar tendon-bone graft, as when this construct is harvested, it is attached firmly to a block of bone at each end. The bone block is usually held fast in the bone in the tunnels by an interference screw, and this usually gives adequate fixation until the bone block unites with the surrounding bone at about 6 weeks. The femoral bone block is usually positioned close to the tunnel opening into the joint, so that there is no abrasion of the ligament on the edges of the tunnel (windscreen wiper effect).
Grafts with no bone block
Hamstrings tendon grafts (usually these days termed a "four-strand" hamstrings", where harvested semitendinosus and gracilis tendons are laid side-by-side and then folded over to make four strands), do not have such bone blocks, and there is a risk of damaging the soft tissue ends of the graft by the fixation device chosen.
Femoral side
If one considers firstly the fixation on the femoral end of the graft, there are a number of choices -
Fixation on the outside of the bone (cortical fixation), eg Endobutton
The Endobutton is a thin oblong button. It is attached at its centre to a thread which is itself looped through the end of the graft. The button can be pulled along the tunnel until the tunnel emerges, and then it is turned on its side and locks itself against the wall of bone.
Fixation through the substance of the bone (transfixation), eg Transfix
At the femoral outlet, a Transfix bar passed through the loop can hold the upper (proximal) end in position, but where the graft emerges into the joint it is unfixed and may 'windscreen wipe' over the bony edge of the tunnel. This is also the case with the endobutton.
Fixation via the tunnel (interference fixation), eg RCI interference screws
An interference screw is screwed alongside the graft within the tunnel itself, pushing the graft against the back wall of the tunnel.
Tibial side
Tibial fixation may be achieved with a screw and washer system or an interference screw.
Fixation device failure
The fixation itself may fail in a variety of ways:
Non-union of bone block
Bone blocks seldom give cause for concern, but in some patients bony union may fail.
Migration of fixation device
Endobuttons may migrate, flip vertically, and slip back into the tunnel or even the joint space if the bone tunnels are too wide or the tensioning inadequate. Interference screws may also migrate into the tunnel.
Breakage of fixation device
Although titanium is a very strong metal, devices such as the endobutton or the Transfix may suffer mechanical failure of the metal.
PREVIOUS PART: ACL graft failure due to graft impingement
NEXT PART: ACL graft failure due to failure to address associated instabilities